Quotation of License Plate Recognition System_ Welcome to Consult - Tigerwong

The license plate recognition system does not only have the above functions_ Welcome to consult. It can also record the appearance of the driver and the time when the vehicle entered. In case of some accidents, such as, etc., it can also provide some assistance to the police in solving the case through monitoring and video recording. After the license plate recognition system is installed in the toll parking lot, the above problems can be easily solved. If the owner accidentally loses the ticket card, the management personnel of the parking lot can check the entry and exit time of the car through this system, and even the appearance of the driver, so as to avoid some unpleasant occurrences, improve the travel time and enhance the customer experience.

It can be seen everywhere in life. But how to stop the device? The following post box will share with you: Earth excavation. The earth excavation adopts mechanical excavation to a height of 200mm above the design elevation. Everyone must not be unfamiliar with the sentry box. Manual trimming and bottom picking are adopted.

When the excavation reaches the design elevation, the drilling exploration of the foundation pit shall be stopped, and the fragile soil layer found shall be removed until the good soil layer is over excavated, and the part shall be compacted and backfilled to the design elevation in layers with 28 lime soil. After the foundation trench is excavated to the design elevation, the establishment unit, design unit and supervision unit shall check and accept it, and the concrete cushion shall be poured immediately after being signed and approved by many parties. According to the construction arrangement, the foundation of the post box is constructed in two steps, the foundation is constructed in one step, and the ground beam is constructed in the second step. After the foundation satisfying the requirements of the bearing capacity is excavated, tamped, and then the replacement of stone slag powder is stopped. The replacement depth is 600mm, and the replacement width is 200mm on each side of the foundation.

The specification value of the foundation bearing capacity after replacement is required to reach 180kpa. The reinforcement processing must be witnessed and sampled on site before the reinforcement is used, It can be used only after passing the inspection by the inspection center. Two sets of reinforcement processing equipment and reinforcement processing machinery. Prior to the blanking of reinforcement, the reinforcement batching list must be prepared in strict accordance with the design drawings and construction specifications and submitted to the project department for review. When cutting reinforcement, the loss length during reinforcement welding shall be considered.The reinforcement is batched intensively on site, which is mainly arranged to be processed and formed on site. The reinforcement is listed according to the model and stacked by category. Stirrups shall be stacked uniformly according to specifications and sizes. Electroslag pressure welding shall be adopted for the connection of reinforcement to frame column, frame beam and foundation reinforcement vertically and lap welding shall be adopted horizontally. However, the position of reinforcement joint shall comply with the rules of construction specifications.

When electroslag pressure welding is adopted, the welded joints set in the same member shall be staggered from each other. In the section from the center of any joint to the length of 35 times the diameter of the reinforcement and not less than 500mm, the same reinforcement shall not have two joints; The cross-sectional area of the tensile reinforcement of the joint shall not exceed 50% of the total area, and the compression area shall not be used. The same reinforcement cannot have two joints in the same section. The spacing between the joints of vertical reinforcement and the floor shall meet the design requirements. Formwork engineering is an important part of concrete structure engineering.

The formwork and its support must have sufficient strength, stiffness and stability, and can reliably accept the self weight, lateral pressure and construction load of reinforcement and concrete, so as to ensure the correctness of engineering structure and component geometric dimensions and mutual positions. Therefore, the construction of formwork engineering is very important and the key of construction. Explain in detail how to install computers and other equipment in the pavilion, and quote for the license plate recognition system_ Welcome to consult. Implement real-time and efficient traffic management, and integrate traffic management, alarm and help, convenient service, prevention and control and disposal. One kiosk has multiple functions, making its functions more detailed and diversified. I'm afraid this should be the new mission of the "three foot Xiaogang Pavilion". Transmission refers to sending the number, speed value and other information obtained at the speed measuring point to the license plate recognition system at the entrance reward point_ Welcome to consult.

In order to punish speeding vehicles. There are two ways to transmit data: uploading all vehicle records and uploading overspeed vehicle records. The latter method transmits a small amount of data, but needs to consider the consistency with the overspeed specification of the back-end management software. Although the former method has a large amount of data, because all vehicle records are transmitted to the back-end management system, It provides considerable flexibility for changing the overspeed limit specification and setting a variety of blacklists. The transmission is grasped by various brands to provide the real-time value of vehicle passing through.Speed measurement can also be installed on the road, and the license plate recognition system can not only be used in parking lots and other places. It can also identify the stolen vehicles running on the road. Of course, this requires the police to establish a stolen vehicle database, and then connect this database to the monitoring system. Once the stolen vehicles are monitored, the police can be notified in time to assist the police in the detection work. This system also has broad application prospects in the field of vehicle security and anti-theft.Based on its function and various problems existing in various parking lots and transportation fields, for example, with the increase of rural population, vehicles will certainly increase, and the problems will also increase. Some of these problems can not be solved only by manpower, so the automatic license plate recognition system is more and more widely used, It is closely related to social development and people's living needs.