Which Fence Gate Is Good? Promise and Keep Your Word - Tigerwong

The gateway shall support flexible, efficient and self-service access; We should be able to serve people with different management demands when customers need them. For example, toll collectors, property management, finance, administrators, groups, merchants, customer service centers, guides, etc. provide different types of mobile management terminal interfaces to realize flexible, convenient and efficient management; After more than two hours of hot melting and other surface treatment processes, the box: pickling, phosphating and electrostatic spraying of polyester powder will enter the drying room with a high temperature of 295 . In order to obtain excellent weather resistance, scratch resistance, UV resistance and color fastness. Main structure of automatic gate: the intelligent automatic gate is installed at the entrance and exit of the parking lot, about 3M away from the controller. It is a mechatronics product integrating magnetic, electrical and mechanical control, which is composed of box, motor, clutch, mechanical transmission part, railing, electronic control, etc. The main structure of the electric gate shall not be changed arbitrarily. The knob, sensor and control box shall operate normally after passing the commissioning.

So as not to lose the good working state and affect the use effect. The driving parts and assembled fasteners shall be inspected regularly to prevent looseness and defect and ensure the normal operation of the door leaf. Transmission refers to sending the number, speed value and other information obtained from the speed measuring point to the entrance reward point. Which one is good in Chongqing barrier gate? Promise to keep your word. In order to punish speeding vehicles.

The amount of data transmitted by the barrier includes uploading all vehicle records and uploading overspeed vehicle records. The latter method transmits a small amount of data, but needs to consider the consistency with the overspeed specification of the back-end management software. Although the amount of data in the former method is large, all vehicle records are transmitted to the back-end management system, It provides considerable flexibility for changing the overspeed limit specification and setting a variety of blacklists. The transmission is grasped by various brands to provide the real-time value of vehicle passing through. The speed measuring magnetic line of force is weakened by the affected magnetic field and picked up by the magnetoelectric inductor.

After the induction coil is wound and energized, the coil will have low-frequency oscillation. When metal enters the coil. Corresponding action occurs. The induction strength of the induction coil is closely related to the number of turns and the shape of the coil. Too many coil turns, large input reactance, resulting in open circuit; The number of turns is too small and the input reactance is small, resulting in short circuit. These two conditions will make the work indicator of the magnetoelectric sensor flash quickly. The general number of turns is 68. Loose screw: the movable joint screws are connected with positive and negative threads, and Shapingba single-layer fence gate.

The upper and lower bearings are connected by double headed screws. If the screws are loose, the upper and lower positions will be inaccurate. Insert an 80mm long 4 iron rod between the double headed screws and rotate the adjusting brake rod up and down in place. Loose coil embedding: when the local sensing coil cannot be firmly fixed in the nest, the vibration of the vehicle over the road will form the coil deformation in the nest and change the initial inductance of the ground sensing. At this time, the sensor must be reset and the front can work normally.

The solution is to pour the melted asphalt into the to fix it. Cut the ground 10cm deep, when wiring the ground induction coil. 2x0.8m square groove, with four corners cut into 45 degree bevel. Place the ground induction coil (1 mm2) in a circle, with a total of 6-8 layers. The coil must be pressed between each layer. Do not have connectors in the coil.The output end of the ground induction coil is twisted to the track gate. And the distance shall be as short as possible. Seal the groove with dry cement after connection. Note: for the high-temperature copper conductor with the cross-sectional area of the ground induction coil of 0.51.5 mm2, the cross-sectional area of the wire does not have a great impact on the induction strength. Precautions in the process of gate device: the gate equipment must be operated according to the wiring diagram when wiring.After connecting the line, first test whether the ground sense is normal. When the ground sense red light flashes, put an iron plate above the coil. When the red light is on for a long time, take away the iron plate, and the automatic falling of the gate is normal.