Only When the All-in-one License Plate Recognition Machine Is Correctly Installed Can the New Featur

The progress of science and technology will drive economic development. Of course, the ultimate goal is to improve people's quality of life. With more and more science and technology joining the parking lot system in recent years, license plate recognition technology is one of them, which gradually alleviates people's parking problems. Today, with the rapid development of vehicles, many single systems are difficult to meet people's needs. Development and innovation is the new direction to solve the parking problem.

People's demand for cars is increasing, and the parking problem has seriously affected our life. The parking system manufacturer has added a comprehensive new equipment - license plate recognition all-in-one machine. License plate recognition all-in-one machine, also known as license plate recognition integrated camera, is a new equipment after the emergence of license plate recognition parking lot system. Because it has the characteristics of high integration and simple installation and commissioning, it can be used directly by inserting a network cable after the equipment is transported to the site, so it is called integrated equipment. Because it has the above characteristics, it can be used in any place, eliminating manual management and saving management cost in the parking lot.

Of course, there is also some stress in its installation process. Only when it is installed correctly can it give full play to its due characteristics. In the face of different parking lot modes, the installation of all-in-one license plate recognition machine is also different. In the final analysis, it is to output license plate recognition results quickly and accurately and take high-quality license plate pictures. I. the straight lane of the parking lot is an ideal installation environment.

When the vehicle drives into the identification area, it can obtain high-quality photos. 1. During construction, the integrated license plate recognition machine and the road gate can be installed on the same side of the lane, but the integrated license plate recognition machine shall be installed in front of the road gate with a spacing of no less than 30cm to avoid mutual interference between equipment. 2. When capture recognition and video recognition are adopted, the best distance between the ground induction coil and the integrated machine is 4m. 3. When the video plus ground sensing recognition mode is adopted, the best distance between the ground sensing coil and the all-in-one machine is 3M. II. Wide lane installation. If the vehicle comes from two directions, double cameras can be installed, and each camera can shoot the incoming vehicle in one direction. 1. If the lane is very wide and the driving direction of the vehicle is not fixed, when the vehicle enters, the front of the vehicle will tilt left and right, which is easy to affect the recognition effect. You can divide the lane into two or separate a non motorized lane with cone barrels, road piles and other obstacles, so as to narrow the motorized lane and straighten the driving direction. 2. If the lane is very wide but cannot be separated into two lanes or add non motorized lanes, double cameras can be installed, that is, an all-in-one license plate recognition machine can be installed on both sides of the lane, so that the license plate can be photographed and recognized by the camera no matter which side the vehicle direction is biased. 3. If the lane is very short, when the car comes from a certain direction, the body is usually inclined to one side. In this case, the camera can be installed on the side to which the front of the car is biased, so that the front of the car is facing the camera when taking pictures. III. when installing the license plate recognition equipment in the curve, the vehicle direction points to the outside of the curve, so the integrated license plate recognition machine should be installed on the outer side of the lane, so that when the vehicle drives into the recognition area, the parking camera can take more positive license plate photos.

IV. basement installation when it is necessary to install the integrated license plate recognition machine in the basement, the following principles shall be followed: the integrated license plate recognition machine at the entrance shall be installed on the horizontal road above the basement ramp, and the integrated license plate recognition machine at the exit shall be installed on the horizontal ground below the basement ramp. In this way, it can avoid that when the integrated machine cannot recognize the license plate, resulting in the failure of the gate to lift, The problem that vehicles can only park on the basement ramp. In order to adapt to various scenarios, there are also various parking lot installations, and the equipment installation mode will change accordingly. The parking lot system will change with science and technology, and some subsystems will change with different crowd and parking mode, which will only be eliminated, The emergence of the integrated license plate recognition system makes the parking lot management simpler and simpler, the equipment stability better and better, and makes it more convenient for people to park. Tigerwong parking equipment supplier has focused on parking equipment for many years! If you have any questions about the parking system, welcome to consult and communicate.