TGW គឺ ជា ការ រចនា និង ដំណោះស្រាយ សម្រាប់ ប្រព័ន្ធ ការ គ្រប់គ្រង សារ 

How to Install the Access Control? How Can It Be Standardized_ Taigewang Technology

How to install access control? How to install access control is the norm? I believe this is a problem often encountered by many construction personnel. Last time, we briefly introduced the selection of access control location and the idea of selecting cables. This time, we will make a specific introduction to the installation process of access control system and the specific installation of equipment. Before that, let's talk about the laying of pipelines. Access control system can be divided into local pipeline and system pipeline. Local pipeline generally refers to the wiring of card reader, controller, electric lock and before opening the door; System pipeline refers to the connection between controllers and power lines. The laying of local pipelines and system pipelines can be crossed or parallel, but the following points should be paid attention to. In order to avoid signal interference, the power line and signal line shall pass through pipes respectively, and the distance between the two pipes shall be more than 30cm; The power supply shall comply with the specifications. Generally, 220V AC is supplied to each access control point through the management center. If the nearby power supply is adopted, pay attention to the relevant specifications; For future maintenance and commissioning, pay attention to marking when threading, and the connector shall be placed in the junction box. Well, having finished the precautions for laying pipelines, let's take a look at the specific installation of sensing head, controller, electric control lock and other equipment. Installation of access control sensing head the following points shall be paid attention to in the installation of sensing head: pay attention to dust prevention during installation and try to avoid dust entering the sensing head; The sensor head shall be installed as close as possible to the control door; In order to avoid interference, the installation position of the sensing head shall be far away from the magnetic field. If it is installed on a metal object, the metal shall be cut off and padded up by about 2 cm. In order to facilitate future maintenance and installation, the wiring in the wall hole shall be neat and orderly; In order to avoid man-made damage to the greatest extent, the access controller should be installed indoors, and the installation position of the controller should be as close to the sensor as possible, generally about 120 meters; For the selection of controller screws, the controller mounting panel shall be fastened with self tapping screws; After installation and commissioning, the controller shall be locked to ensure safety. When installing and transforming the door, the power line and control line shall be laid in advance, buried in the door or door frame, and a certain length shall be reserved to access the electric lock. During installation, the electric lock and lock catch shall be tested and debugged, the bite shall be accurate, and it can expand and retract normally when opening and closing the door; The installation of electric control lock shall not be simple. It is required to lock the door smoothly. For example, the female lock and male lock shall be able to close the door without obvious looseness; The plug-in lock or electric clip lock shall be flush with the corresponding door or door shaft after locking; The magnetic lock should not feel obvious impact when closing the door vigorously. It is better to install the door closer.

How to Install the Access Control? How Can It Be Standardized_ Taigewang Technology 1

TGW-TT005 គំរូ រវាង Tripod Turnstile Semi ស្វ័យ ប្រវត្តិ TGW- TTT008 Tripod Turnstile ដៃ ប្រព័ន្ធ ត្រួតពិនិត្យ ការ ចូល ដំណើរការ ដោយ ដៃ PARK-105 ប្រព័ន្ធ ជែក ក្រហម រង់ ផ្នែក ដោយ ស្វ័យ ប្រវត្តិ TGW- LLST003 ចន្លោះ បញ្ចូល បញ្ជា ឆានែល កម្មវិធី បញ្ជា គ្រប់គ្រង ការ រៀបចំ ធីក ដែល មាន កម្មវិធី អាន កាត rfid ដែល មាន ម៉ាស៊ីន ថត សម្រាប់ ការ រក ឃើញ TGW-NAC Ultrasonic parking guidance car sensors parking lot sensors systems TGW- LLST018 Turnstile Waist Height Swing Turnstile Troel Barrier Swing Turnstile TGW- FH002D ប្រព័ន្ធ ស្វ័យ ប្រវត្តិ បម្រុង ទ្វេល កម្ពស់ ពេញលេញ TGW-TBCG ប្រព័ន្ធ TGW-SMHT ការ ទទួល យក រូប តំណាង ម៉ាស៊ីន ថត ការ ចូល រួម ទម្រង់
អត្ថបទក្តៅ ៗ
របៀប បិទ ALPR
ប្រព័ន្ធ បញ្ជា ចូល ដំណើរការ
We are in the era of face recognition access control
តើ ជា អ្វី ការ ទទួល ស្គាល់ លេខ បណ្ដាញ ស្វ័យ ប្រវត្តិ ?
ប្រព័ន្ធ Alpr
ប្រព័ន្ធ ការ ទទួល ស្គាល់ ប្លុក អាជ្ញាប័ណ្ណ
License plate recognition company
IoT Based Smart Parking System Project Using NodeMCU ESP8266 - IoT Design Pro - IoT Projects, Articl
Reverse Engineering a Cat Genie to Bypass the Razor-and-Blades Business Model
ZKTeco POS POS Terminals | POS Software and POS Accessories
lpr parking solutions អត្ថបទ​ដែល​ទាក់ទង
What Is a License Plate Recognition System_ Taigewang Technology
If You Want to Upgrade the Parking Lot, You Must First Understand the Applications of the Parking Lo
Three Main Development Trends of Parking Lot Charging System in the Future_ Taigewang Technology
Is It Good to Install a Location Guidance System in the Parking Lot_ Taigewang Technology
License Plate Recognition Technology Opens the Sky Eye of Intelligent Transportation_ Taigewang Tech
Shenzhen TGW Technology Co., Ltd គឺ ជា កម្មវិធី ផ្ដល់ ការ បញ្ជា បញ្ជា ចូល ដំណើរការ មែន សម្រាប់ ប្រព័ន្ធ កញ្ចប់ កម្រិត ខ្សែស្រឡាយ ប្រព័ន្ធ ការ ទទួល ស្គាល់ ប្លុក អាជ្ញាប័ណ្ណ និង ការ ចូល ដំណើរការ បញ្ជា រហូត និង ស្ថានីយ ការ ទទួល ស្គាល់ រាល់ គ្នា ។

Shenzhen TigerWong Technology Co., Ltd

ទូរស័ព្ទ ៖86 13717037584

អ៊ីមែល៖ Info@sztigerwong.comGenericName

បន្ថែម ៖ ជុំ 601-6000   ឡុងទហា កណ្ដាល ឡុង ហ៊ូ វ៉ាន


រក្សា សិទ្ធិ©2021 Shenzhen TigerWong Technology Co., Ltd   | បណ្ដាញ
Please message us and we’ll be sure to respond ASAP, what product you intrested in?
contact customer service